Re: [IRCA] SDR-Console and the Perseus SDR Volume Levels

[Les Rayburn <les@xxxxxxxxxxxxxxxx>]

Don,

I was advised that if you lowered the sampling rate to 950, the Perseus 
could record 1750 KHz worth of bandwidth (the entire AM band). Have you 
tried that? I assume quality might suffer a bit, but that might be 
offset by the ability to record the entire band.


Les Rayburn, Director
High Noon Film
130 1st Avenue West
Alabaster, AL 35007-8536
(205) 621-7500
(205) 621-7505 FAX
(205) 253-4867 CELL
http://www.highnoonfilm.com

---------------------------------------------

This e-mail contains information that may be confidential or privileged 
and is intended only for the person(s) named above.
Any other distribution, copying or disclosure is strictly prohibited. If 
you have received this e-mail in error, please
notify the sender immediately and return the original transmission to 
the above address by mail without making a copy.

On 2/25/2014 1:02 PM, Don Moman VE6JY wrote:
> There is a volume tab in the SDR Console next to the speaker icon in the
> VFO pane. Even tho it says 75 the actual level may be anything - it is just
> an icon.
>
> Using the native Perseus software recording is 1600 khz maximum - it
> records what you have the screen width set to.
>
> 73 Don
> VE6JY
>
>
> On Tue, Feb 25, 2014 at 5:49 PM, Les Rayburn <les@xxxxxxxxxxxxxxxx> wrote:
>
> > Got the new Perseus SDR hooked up and running last night using SDRV4.1
> > downloaded from the Perseus web site. No problems at all with the initial
> > installation on Windows 7 Pro. Had it working within moments.
> >
> > One issue I did notice was that when I used the Perseus with the
> > SDR-Console software, the AF output volume was much lower compared to the
> > native Perseus software. No idea why this would be, and couldn't find a
> > place to adjust the level inside the SDR-Console software. Can someone
> > offer assistance?
> >
> > RF levels appeared to be the same for both software.
> >
> > So far, I love the Perseus! One other question--how much bandwidth can the
> > Perseus record in I/O mode? I've seen some sites that say it's limited to
> > 800 KHz, others say 1600 KHz, and others 2 MHz. My understanding is that it
> > would cover the entire AM band, which would be 1710 KHz (1.7 MHz)
> >
> >
> > --
> > 73,
> >
> >
> > Les Rayburn, N1LF
> > Maylene, AL
> > EM63
> >
> > Member NRC, IRCA, & Medium Wave DX Circle
> > Former CPC Chairman for NRC/IRCA
> >
> > SDR-IQ,Funcube Pro, Wellbrooke ALA-1530+ loop, LF Engineering Active Whips,
> > Quantum Phaser, Kiwa Loop, Palstar MW Pre-Selector
> >
> > _______________________________________________
> > IRCA mailing list
> > IRCA@xxxxxxxxxxxxxxxx
> > http://montreal.kotalampi.com/mailman/listinfo/irca
> >
> > Opinions expressed in messages on this mailing list are those of the
> > original contributors and do not necessarily reflect the opinion of the
> > IRCA, its editors, publishing staff, or officers
> >
> > For more information: http://www.ircaonline.org
> >
> > To Post a message: irca@xxxxxxxxxxxxxxxx
> _______________________________________________
> IRCA mailing list
> IRCA@xxxxxxxxxxxxxxxx
> http://montreal.kotalampi.com/mailman/listinfo/irca
>
> Opinions expressed in messages on this mailing list are those of the original contributors and do not necessarily reflect the opinion of the IRCA, its editors, publishing staff, or officers
>
> For more information: http://www.ircaonline.org
>
> To Post a message: irca@xxxxxxxxxxxxxxxx


--
73,


Les Rayburn, N1LF
Maylene, AL
EM63

Member NRC, IRCA, & Medium Wave DX Circle
Former CPC Chairman for NRC/IRCA

SDR-IQ,Funcube Pro, Wellbrooke ALA-1530+ loop, LF Engineering Active Whips,
Quantum Phaser, Kiwa Loop, Palstar MW Pre-Selector

_______________________________________________
IRCA mailing list
IRCA@xxxxxxxxxxxxxxxx
http://montreal.kotalampi.com/mailman/listinfo/irca

Opinions expressed in messages on this mailing list are those of the original contributors and do not necessarily reflect the opinion of the IRCA, its editors, publishing staff, or officers

For more information: http://www.ircaonline.org

To Post a message: irca@xxxxxxxxxxxxxxxx