[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [IRCA] Google Earth as a DX aid
- Subject: Re: [IRCA] Google Earth as a DX aid
- From: "Neil Kazaross" <neilkaz@xxxxxxxxxxxxx>
- Date: Sun, 24 Aug 2008 20:31:27 -0500
- Authentication-results: mx.google.com; spf=pass (google.com: domain of irca-bounces@xxxxxxxxxxxxxxxx designates 64.15.155.228 as permitted sender) smtp.mail=irca-bounces@xxxxxxxxxxxxxxxx; domainkeys=hardfail (test mode) header.From=neilkaz@xxxxxxxxxxxxx
- Domainkey-signature: a=rsa-sha1; q=dns; c=nofws; s=dk20050327; d=earthlink.net; b=tvJK6DwXe4p+F7iZotcTeaVB9yO7T4j9Jaq6TukutVX6vrwjEwuBDfK+lAlwNF2u; h=Received:Message-ID:Reply-To:From:To:References:Subject:Date:MIME-Version:Content-Type:Content-Transfer-Encoding:X-Priority:X-MSMail-Priority:X-Mailer:X-MimeOLE:X-ELNK-Trace:X-Originating-IP;
- Domainkey-status: bad (test mode)
Chris,,thx for the great tip which I made good use of today. My neighbor to
the west gave me permission to run BOGs thru his woods behind his house and
yard. However, trying to keep wire straight for hundreds of feet thru thick
woods isn't easy during full foliage of everything including undergrowth. I
can sort of see his house and tell where the end of his back lawn is and
near the end of the wire, ditto for my more westerly neighbor, but with the
arial view from google earth I wasn't sure how far to stay away from the
edges of their lawns while keeping basically due west ..well 272 deg.
Anyhow, I got the 335 ft down in his yard today in about 2 hours and have
about 150 ft and less dense woods on my land to go thru and then 450 feet
easy to hook up to my DX truck. Thus I expect to be trying a 935 ft BOG
tomorrow night.
73 KAZ Barrington IL
----- Original Message -----
From: "CHRIS KNIGHT" <cgknight63@xxxxxxx>
To: <irca@xxxxxxxxxxxxxxxx>
Sent: Sunday, August 24, 2008 2:33 PM
Subject: [IRCA] Google Earth as a DX aid
If you didn't already know this, Google Earth is a great tool for finding
DX sites, measuring the length of wire antennas, locating transmitter
sites, etc. To begin, I downloaded Google Earth (version 4.3.7284.39.16
beta). To find the website I searched for "google earth" (in quotes) from
the www.google.com home page.
After Google Earth was installed, I located my old QTH (for example). (At
this point you may open Google Earth and follow along with me). The radio
room window was located exactly at 38 deg 18' 44.17"N 104 deg 42' 54.65"W
(on S. Clarion Dr.). From that point I had a BoG (sometimes elevated 2' or
3' feet above ground) extending from the window to the corner of S.
Purcell Blvd. and S. Datura Drive. To find that location, click on "street
view" in "layers" at the bottom left. Street names will appear. There's a
house there now which didn't exist back in the 1980's.
To measure the length of the Beverage antenna, click the ruler in the
toolbar. This brings up a small window entitled "Ruler". To choose the
preferred units of measure (feet, meters or other units of measure) simply
click the down arrow and select the units. Next, click off "mouse
navigation" to set your points of measurement. Click the point you wish to
measure from. If you need to navigate to a point off the screen for the
2nd point, enable mouse navigation making sure to toggle it off again once
you find the 2nd point. Or, you can zoom out using the controls on the
right. For this example click on the old radio room window (at the receive
end of the antenna) at the above coordinates, then click the near the
intersection of the two above streets. The length of the antenna comes out
to be around 750 feet.
If you want a view from ground level, click "street view" in the layers
section. You will notice camera symbols popping up all along the streets.
Click a camera symbol in the area. You can now see the house, the radio
room window and the trees near the house, also the bare prairie where the
antenna once lived.
Once you find a potentially good DX QTH, click on the yellow thumbtack
symbol in the tool bar. You may now place a marker on the location, title
it, and make notes about that location. Once you have saved the placemark,
you may refer back to it by double-clicking the information that appears
in the "places section" on the left center of the screen. To edit a
placemark, right-click it then click "properties". I used this feature to
placemark all of my local and semi-local station transmitter sites, for
example, finding the coordinates from the FCC database.
The resolution of satellite photos varies. In some areas (especially very
remote places) the resolution isn't as good as populated areas. Even so,
Google Earth is still an excellent tool and better yet, it's free!
Does anyone have the coordinates for the famous Grayland DX site?...hi.
73. Chris
Chris Knight
Fort Lupton, Colorado
http://sites.google.com/site/2008amloggings/
_______________________________________________
IRCA mailing list
IRCA@xxxxxxxxxxxxxxxx
http://montreal.kotalampi.com/mailman/listinfo/irca
Opinions expressed in messages on this mailing list are those of the original contributors and do not necessarily reflect the opinion of the IRCA, its editors, publishing staff, or officers
For more information: http://www.ircaonline.org
To Post a message: irca@xxxxxxxxxxxxxxxx