Re: [IRCA] "Airport-Friendly" FSL Antenna Designs

[d1028gary@xxxxxxxxxxx]

The Ukrainian seller on eBay has lowered the listing price for a lot of 30 of the Russian surplus 160mm x 8mm ferrite rods, from $55.95 down to $44.76 (plus $27 shipping, to the U.S.). This means that the ferrite rods used to construct the latest "airport friendly" FSL design (the 3.5" Baby FSL model) can now be purchased for $71.76, instead of $82.95. The "Heathkit-like" full construction article for that model is currently being drafted. 

http://www.ebay.com/itm/30-pcs-Vintage-Ferrite-Rod-8mm-x-160mm-For-Crystal-Radio-/192185405777?hash=item2cbf249151:g:DREAAOSwNuxXaCFE 

73 and Good DX, 
Gary DeBock (in Puyallup, WA, USA) 


----- Original Message -----

From: d1028gary@xxxxxxxxxxx 
To: "Mailing America" <irca@xxxxxxxxxxxxxxxx> 
Sent: Tuesday, May 16, 2017 10:03:03 PM 
Subject: Re: [IRCA] "Airport-Friendly" FSL Antenna Designs 

Chuck, 

If you are making a decision between building the second (3.5") FSL model or the third (4.7") model, you should definitely go for the second (160mm ferrite rod) model. It has a sensitivity "point score" (ferrite length x coil diameter) of 560, whereas the third FSL model has a point score of 292. In addition, the second model uses the highest sensitivity 1162/46 Litz wire, while the third model uses the less sensitive 660/46 type. By comparison, the 5" FSL models used by Craig and I in Hawaii last month have sensitivity point scores of 585 (and also have the most sensitive 1162/46 Litz wire). 

In any case the first "Heathkit-like" full construction article (for the second, recommended, 3.5" FSL model) should be completed in about a month-- which will give any interested DXers the time to order and receive the 160mm x 8mm ferrite rods from the (newly prosperous) eBay sellers in the Ukraine. 

Gary 


----- Original Message ----- 

From: "Chuck Hutton" <charlesh3@xxxxxxx> 
To: "Mailing list for the International Radio Club of America" <irca@xxxxxxxxxxxxxxxx> 
Sent: Tuesday, May 16, 2017 5:32:15 PM 
Subject: Re: [IRCA] "Airport-Friendly" FSL Antenna Designs 

Gary - 


I'd like to see a construction article for the 3.5" and 4.7" models. I'll build one or the other. 


Chuck 


________________________________ 
From: IRCA <irca-bounces@xxxxxxxxxxxxxxxx> on behalf of d1028gary@xxxxxxxxxxx <d1028gary@xxxxxxxxxxx> 
Sent: Tuesday, May 16, 2017 5:18 PM 
To: America, Mailing 
Subject: [IRCA] "Airport-Friendly" FSL Antenna Designs 

Up until very recently it was only a dream to be able to enjoy high-sensitivity MW-DXing in a motel room after long distance air travel. Ultralight radios (hot-rodded and stock) could be packed away for some basic DXing fun, but serious high-gain antennas required either serious packing space, or deployment outside of the motel room (a dubious possibility in most cases). 

In an effort to make high gain MW-DXing possible during long range air travel, a new series of "Frequent Flyer" FSL antennas was developed here over the winter. These antennas were designed to be serious MW-DXing performers, but still have non-subversive appearances, allowing them to routinely pass through TSA security screening at major airports. All of them can easily be carried within standard hand-carry luggage (while protected by matched-sized plastic totes). Because of the increased MW-band sensitivity provided by the new 1162/46 Litz wire, it was possible to shrink the size of the 2012-year 5" Mini-FSL model (providing inductive coupling gain roughly equivalent to that of a 4' air core box loop, fully described at http://www.mediafire.com/file/9ze98h293s85p86/5_inch_FSL.doc 
down to a very compact size, allowing the development of this "Frequent Flyer" FSL series. 

Three new "Frequent Flyer" FSL designs have been built and tested, and two recent Hawaii DXpeditions were conducted with the first of these models. The 5" Bar FSL model (design photo at https://app.box.com/s/2lixzaly97goivq7i3qqj6etrr0ce109 ) was used by Craig Barnes for a very successful trip to Princeville, Kauai (during which about 40 Asian TP's were received on a stock Tecsun PL-310 model), and I had a very enjoyable DXing trip to Kona on the Big Island, receiving exotic Pacific Island DX at S9 levels (fully described at http://swling.com/blog/tag/gary-debock/ This model has successfully passed through airport TSA screening checkpoints 7 times, although the 100mm Russian surplus ferrite bars used in its construction are extremely scare, limiting the number of these models that can be made (only 5 are planned). Performance-wise, through, the following ferrite bar model can provide equivalent MW sensitivity with readily available construction parts. 

The new 3.5" ferrite bar model (design photo at https://app.box.com/s/az7wz583mpgeftw98v04zah7nc9nj4z0 ) was designed to combine high performance with easy construction, and readily available parts. It has a smaller diameter than the above FSL model but longer ferrite length, giving it equivalent MW sensitivity. The 27 Russian surplus 160mm x 8mm ferrite rods can be purchased on eBay for about $70 shipped, giving the model an overall construction cost of about $150 US. It uses the same high-sensitivity 1162/46 Litz wire as the above FSL model, but because of the ferrite rod design it can provide inductive coupling boosts on both the sides of the antenna, as well as in the front or back. A full "Heathkit-like" construction article is planned for this model, similar to the 2012 5" Mini-FSL model article linked above.. 

Finally a "economy-class" 4.7" Frequent Flyer model using the commonly-available Russian surplus 62mm ferrite bars has also been built, with the design photo at https://app.box.com/s/mlnhho99rswvdrp62ik634ft7t5a6s9a . This model can be built for around $65 US, and provides a good inductive coupling boost to a stock Ultralight radio (with greater MW sensitivity than the 7.5" loopstick hot-rodded models). Because of the limited ferrite bar length their isn't enough space to wind the required number of 1162/46 Litz wire coil turns on this model, so 660/46 Litz wire is used instead. That is one of the reasons why the construction cost of this model is significantly lower, since 660/46 is relatively cheap by comparison. Thomas Witherspoon of SWLing.com was kind enough to post an article detailing the runoff of this "economy class" FSL model against the Terk Advantage commercial loop, at http://swling.com/blog/2017/03/daytime-dx-gary-compares-terk-advantage-with-homebrew-fsl-loop/ 
Depending upon interest in this FSL model, a full-construction article may also be written in the future. 

Hopefully these compact, high performance FSL antennas will give DXers some new options for enjoying their hobby during long-range air travel. 

73 and Good DX, 
Gary DeBock (in Puyallup, WA, USA) 
.. 
_______________________________________________ 
IRCA mailing list 
IRCA@xxxxxxxxxxxxxxxx 
http://montreal.kotalampi.com/mailman/listinfo/irca 

Opinions expressed in messages on this mailing list are those of the original contributors and do not necessarily reflect the opinion of the IRCA, its editors, publishing staff, or officers 

For more information: http://www.ircaonline.org 

To Post a message: irca@xxxxxxxxxxxxxxxx 

_______________________________________________ 
IRCA mailing list 
IRCA@xxxxxxxxxxxxxxxx 
http://montreal.kotalampi.com/mailman/listinfo/irca 

Opinions expressed in messages on this mailing list are those of the original contributors and do not necessarily reflect the opinion of the IRCA, its editors, publishing staff, or officers 

For more information: http://www.ircaonline.org 

To Post a message: irca@xxxxxxxxxxxxxxxx 


_______________________________________________ 
IRCA mailing list 
IRCA@xxxxxxxxxxxxxxxx 
http://montreal.kotalampi.com/mailman/listinfo/irca 

Opinions expressed in messages on this mailing list are those of the original contributors and do not necessarily reflect the opinion of the IRCA, its editors, publishing staff, or officers 

For more information: http://www.ircaonline.org 

To Post a message: irca@xxxxxxxxxxxxxxxx 


_______________________________________________
IRCA mailing list
IRCA@xxxxxxxxxxxxxxxx
http://montreal.kotalampi.com/mailman/listinfo/irca

Opinions expressed in messages on this mailing list are those of the original contributors and do not necessarily reflect the opinion of the IRCA, its editors, publishing staff, or officers

For more information: http://www.ircaonline.org

To Post a message: irca@xxxxxxxxxxxxxxxx